DG405DY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG405DY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 2 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. The electronic part body is injected with 16 pins. On the other hand, analog switches can be constructed using DPST - NO switching circuits. Circuits number 2 make up this analogue multiplexer. A 45Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 13V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 15V operating voltages can be used with this electrical part. A 4 input needs to be operated.
DG405DY-T1 Features
2 Channels
Switch Circuit: DPST - NO
DG405DY-T1 Applications
There are a lot of Vishay Siliconix DG405DY-T1 Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Precision data acquisition
- Cable Modem
- Signal routing between systems
- Digital cross connects (DSX-1)
- USB 1.1 signal switching circuits
- Data switching
- Imaging
- Power routing
- Multiplexers
