Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2014 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
55Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG405 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
5μA |
Power Dissipation |
600mW |
Max Supply Current |
1μA |
Throw Configuration |
DPST |
Turn On Delay Time |
150 ns |
Number of Inputs |
4 |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
DPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
60pC |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
35Ohm |
Normal Position |
NO |
Voltage - Supply, Dual (V±) |
±15V |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG405DY-T1-E3 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature around -40°C~85°C TA extended. In total, there are 16 terminations. Due to its 2 channels, the electrical component produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. These analog multiplexers are built based on DPST - NO switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with DG405. The internal resistance of this digital multiplexer is 55Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 13V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 5μA current. When the digital multiplexer is charged above 1μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 7V voltage attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 15V operating voltages can be used with this electrical part. The electrical component supports 4 inputs. This electronic component presents a Drain to Source resistance of 35Ohm.
DG405DY-T1-E3 Features
2 Channels
Switch Circuit: DPST - NO
5μA Supply Current
Drain-to-Source resistance: 35Ohm
DG405DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG405DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Communications systems
- Battery-powered systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multiplexers
- Avionics
- Wireless Local Loop
- Sample-and-hold systems
- E1 Network Equipment
- Communication systems