DG406BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Weight | 4.190003g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 60Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 625mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Pin Count | 28 |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 625mW |
| Max Supply Current | 500μA |
| Propagation Delay | 148 ns |
| Turn On Delay Time | 125 ns |
| Number of Inputs | 16 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 108pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Voltage - Supply, Dual (V±) | ±5V~20V |
| Height | 3.31mm |
| Length | 39.7mm |
| Width | 14.73mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG406BDJ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-DIP (0.600, 15.24mm). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 16:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 28 pins are injected into the body of the electronic part. The multiplexer consists of 1 circuits. An switch multiplexer with 60Ohm internal resistance has a value of 60Ohm. To find out what the 28 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 36V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. 7.5V is the lowest voltage that should be fed to the electronic electronic part. When the digital multiplexer is charged above 500μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 5V. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Operating voltages of 12V are compatible with the electrical part. It is possible to operate 16 inputs.
DG406BDJ Features
16 Channels
DG406BDJ Applications
There are a lot of Vishay Siliconix DG406BDJ Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Optical Applications
- PCMCIA cards
- Multiplexers
- Access Concentrators
- Data Acquisition Systems
- Routers
- Battery Powered Systems
- Audio and video switching
- PBXs
