DG406BDJ-E3
| Parameters | |
|---|---|
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Power Dissipation | 625mW |
| Max Supply Current | 500μA |
| Propagation Delay | 148 ns |
| Turn On Delay Time | 125 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 108pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Voltage - Supply, Dual (V±) | ±5V~20V |
| Height | 3.31mm |
| Length | 39.7mm |
| Width | 14.73mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Weight | 4.190003g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Max Power Dissipation | 625mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
DG406BDJ-E3 Overview
As the electronic part is packed in 28-DIP (0.600, 15.24mm), international shipping is convenient. To ensure high reliability, a new packaging method Tube is used. In Through Hole, this analog switch is mounted. 16:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 28 terminations have been recorded. The electronic part provides high-quality output because it has 16 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. This electrical component is included in the 28 series of products. The multiplexer consists of 1 circuits. Try searching for DG406 variants of the analog switch ic. The internal resistance of this digital multiplexer is 100Ohm. For functions related to 28 pins, please refer to the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Digital switch that provides Dual, Single power at a cost-effective price. 7.5V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 30μA current. A digital multiplexer may suffer damage if voltage is applied above 500μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 5V voltage attached. The electrical part can be operated at 12V voltage levels. It is possible to operate 16 inputs.
DG406BDJ-E3 Features
16 Channels
30μA Supply Current
DG406BDJ-E3 Applications
There are a lot of Vishay Siliconix DG406BDJ-E3 Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- High speed data transmission line cards
- Signal routing between systems
- DSUs
- HDTV
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics and Military Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Access Concentrators
- Fiber In The Loop (FITL)
