DG406BDN-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Propagation Delay | 163 ns |
| Turn On Delay Time | 125 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 108pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Voltage - Supply, Dual (V±) | ±5V~20V |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| RoHS Status | ROHS3 Compliant |
DG406BDN-E3 Overview
The electrical component comes in 28-LCC (J-Lead) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Surface Mount is this multiplexer. 16:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. There are 28 terminations totally. A 16 channel electronic part produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 28 pins. There are 1 circuits in this multiplexer. Use DG406 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 100Ohm. The functions of 28 pins can be found in the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 7.5V. The analogue multiplexer could operate on 30μA current. Putting voltage greater than 500μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 5V. Operating voltages of 12V are compatible with the electrical part. There are 16 inputs to be operated.
DG406BDN-E3 Features
16 Channels
30μA Supply Current
DG406BDN-E3 Applications
There are a lot of Vishay Siliconix DG406BDN-E3 Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- MP3 players
- Audio signal routing
- Channel Banks
- Residential Gateways, Home Gateway/Router
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- Industrial control systems
- Industrial
