DG406BDW-E3
| Parameters | |
|---|---|
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 30μA |
| Max Supply Current | 500μA |
| Propagation Delay | 148 ns |
| Turn On Delay Time | 125 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 108pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 2.34mm |
| Length | 17.91mm |
| Width | 7.49mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Weight | 792.000628mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
DG406BDW-E3 Overview
This electronic part is conveniently packaged in 28-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, you'll find this switch device. 16:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~85°C TA are extended for operation. 28 terminations have been made so far. As a result of its 16 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. Electronic part bodies are injected with 28 pins. A 1 circuit is present in this switch device. Try searching for the analog switch ic with DG406 if you are looking for variants. In this multiplexer, the internal resistance is 100Ohm. For functions related to 28 pins, please refer to the datasheets. Users should never supply a voltage higher than 36V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 7.5V should be applied to the electronic component. 30μA current would be enough for this multiplexer to operate. A digital multiplexer may suffer damage if voltage is applied above 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 5V if you are using dual power supplies. This electrical part is compatible with 15V operating voltages.
DG406BDW-E3 Features
16 Channels
30μA Supply Current
DG406BDW-E3 Applications
There are a lot of Vishay Siliconix DG406BDW-E3 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Precision test equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Central office
- Audio and video signal routing
- Digital cross connects (DSX-1)
- Avionics test equipment
- Transmit
- Communication systems
- Industrial and process control systems
