Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
28-SOIC (0.295, 7.50mm Width) |
Number of Pins |
28 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2000 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
175Ohm |
Max Power Dissipation |
1W |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG406 |
Pin Count |
28 |
Operating Supply Voltage |
28V |
Number of Channels |
16 |
Number of Circuits |
1 |
Max Supply Voltage |
30V |
Min Supply Voltage |
5V |
Operating Supply Current |
500μA |
Propagation Delay |
300 ns |
Turn On Delay Time |
600 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
5V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
300 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
16:1 |
Off-state Isolation-Nom |
69 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
8pF 130pF |
On-state Resistance Match-Nom |
1.5Ohm |
Switch Time (Ton, Toff) (Max) |
200ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.5 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
400ns |
Signal Current-Max |
0.02A |
Height |
2.35mm |
Length |
18.1mm |
Width |
7.6mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG406CWI+ Overview
The electronic component is convenient to ship overseas because it is packed in a 28-SOIC (0.295, 7.50mm Width). This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 16:1. Extended operating temperature around 0°C~70°C TA. The total number of terminations is 28. A high-quality output is provided by the electrical component's 16 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 28 series. A 1 circuit is present in this switch device. Use DG406 to search for variants of the digital switches. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. The functions of 28 pins can be found in the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 500μA current. Despite this switch's dual supply capability, its voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. 28V operating voltages are supported by the electronic component.
DG406CWI+ Features
16 Channels
500μA Supply Current
DG406CWI+ Applications
There are a lot of Maxim Integrated DG406CWI+ Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- PDAs
- Audio signal routing
- RGB switches
- Multiplexers
- Mechanical reed relay replacement
- Data Acquisition Systems
- Automatic test equipment
- 65 V DACs
- Intelligent PBX