DG406DJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Signal Current-Max | 0.02A |
| Height | 4.45mm |
| Length | 37.34mm |
| Width | 14.61mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG406DJ+ Overview
As the electronic part is packed in 28-DIP (0.600, 15.24mm), international shipping is convenient. The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Through Hole position. There is 16:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. 28 terminations have been made so far. By its 16 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electrical component is included in the 28 series of products. The multiplexer consists of 1 circuits. If you are looking for variants of the digital switch, trying search with DG406. It has an internal resistance of 175Ohm. For functions related to 28 pins, please refer to the datasheets. Multiplexers should not be powered above 30V in normal situations. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 5V should be applied to the electronic component. In order to operate this switch device, it would need a current of 500μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. With dual power supplies, you should attach at least 4.5V. There is a voltage range of 28V operating voltages for the electrical part.
DG406DJ+ Features
16 Channels
500μA Supply Current
DG406DJ+ Applications
There are a lot of Maxim Integrated DG406DJ+ Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Transmit
- Switching Systems
- Sample-and-hold systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
- Routers
- Signal routing between systems
- Audio and video routing
- Low-Voltage
