DG406DN-E3
| Parameters | |
|---|---|
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Drain to Source Resistance | 100Ohm |
| Signal Current-Max | 0.02A |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG406 |
DG406DN-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-LCC (J-Lead). The advanced packaging method Tube provides high reliability. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 16:1. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 28. This electronic part offers high-quality output due to its 16 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. Into the electrical component body are injected 28 pins. The multiplexer consists of 1 circuits. Try searching with DG406 if you're looking for variants. It has an internal resistance of 50Ohm. The datasheets for the 28 pins explain the functions. In normalcircumstances, users should not exceed 44V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 7.5V. The switch device would be able to operate with 30μA current. Put voltage above 500μA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. It is recommended that you attach at least 5V to your dual power supply. 15V operating voltages are supported by the electronic component. There are 16 inputs to be operated. This electronic component presents a Drain to Source resistance of 100Ohm.
DG406DN-E3 Features
16 Channels
30μA Supply Current
Drain-to-Source resistance: 100Ohm
DG406DN-E3 Applications
There are a lot of Vishay Siliconix DG406DN-E3 Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Relay Replacement
- SONET/SDH ADM
- PDH Multiplexers
- CSU
- PDAs
- Multiplexers
- Audio signal routing
- Precision data acquisition
- USB 1.1 signal switching circuits
