DG406DN-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Number of Functions | 1 |
| Reach Compliance Code | unknown |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 7.5V |
| Analog IC - Other Type | DPDT |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 600 ns |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| RoHS Status | Non-RoHS Compliant |
DG406DN-T1 Overview
Presented in 28-LCC (J-Lead), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 16:1. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 28 terminations. A high-quality output is provided by the electrical component's 16 channels. There are 1 circuits in this switch device. Analog switches have 100Ohm internal resistance. For details about the functions of 28 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 44V. An effective Dual, Single supply digital multiplexer. A low voltage of 7.5V should be applied to the electronic component. A digital multiplexer may suffer damage if voltage is applied above 500μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 5V to your dual power supply. Integrated with an analog IC DPDT. It can operate from 15V operating voltages. The electrical component supports 16 inputs.
DG406DN-T1 Features
16 Channels
DG406DN-T1 Applications
There are a lot of Vishay Siliconix DG406DN-T1 Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- SDH/SONET multiplexers
- Avionics test equipment
- DSUs
- Voice over IP/DSL – Integrated Access Devices, Smart
- Battery Powered Instruments
- High-Voltage
- Sample-and-hold systems
- E1 Network Equipment
- Battery-powered systems
