DG406DN-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG406DN-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 28-LCC (J-Lead). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. 16:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there are 28 terminations. The electronic part delivers high-quality output through its 16 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. As part of its design, the 28 series is equipped with this electronic component. A 1 circuit is present in this switch device. DG406 can be used to search for analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for functions of 28 pins are available. Multiplexers should not be powered above 44V in normal situations. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 7.5V. 30μA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 500μA. Despite this switch's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 5V voltage attached. The electrical part can be operated at 15V voltage levels.
DG406DN-T1-E3 Features
16 Channels
30μA Supply Current
DG406DN-T1-E3 Applications
There are a lot of Vishay Siliconix DG406DN-T1-E3 Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Digital access cross connects
- Cell phones
- Cable PC
- Fiber In The Loop (FITL)
- Microprocessor Controlled Analog Systems
- Audio signal routing
- Multiplexers
- Data switching
- HDTV
