DG406EUI-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 175Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Power Dissipation | 1.025W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 75μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Length | 9.7mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG406EUI-T Overview
The electrical component comes in 28-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. 16:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. There are 28 terminations totally. Due to its 16 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 28 series. The circuits in this analogue multiplexer number 1. Look for analog switch ic variants by searching with DG406. This digital multiplexer has 175Ohm internal resistance. Please refer to the datasheets for 28 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 5V should be the lowest voltage fed to the electronic component. 75μA current would be enough for this multiplexer to operate. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. With dual power supplies, you should attach at least 4.5V. 28V operating voltages are supported by the electronic component.
DG406EUI-T Features
16 Channels
75μA Supply Current
DG406EUI-T Applications
There are a lot of Maxim Integrated DG406EUI-T Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Communication systems
- Transmit
- Data Acquisition Systems
- FTTH
- Fiber to the Home
- Audio/video switches
- Low-Voltage
- Microprocessor controlled systems
- Communications systems
