DG406EWI+T
| Parameters | |
|---|---|
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG406 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 75μA |
| Propagation Delay | 450 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
DG406EWI+T Overview
Packed in 28-SOIC (0.295, 7.50mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 16:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 28 terminations. By its 16 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of its design, the 28 series is equipped with this electronic component. There are 1 circuits in this multiplexer. Use DG406 to search for variants of the digital switches. In this multiplexer, the internal resistance is 175Ohm. To find out what the 28 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 5V voltage fed to the electrical part below 5V. In order to operate this switch device, it would need a current of 75μA. Despite this switch's dual supply capability, its voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. It can operate from 28V operating voltages.
DG406EWI+T Features
16 Channels
75μA Supply Current
DG406EWI+T Applications
There are a lot of Maxim Integrated DG406EWI+T Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Relay replacements
- Voice over IP/DSL – Integrated Access Devices, Smart
- Precision test equipment
- Automotive applications
- DSLAMs
- Battery Powered Systems
- Communication systems
- Cell phones
- Central office
