DG407BDJ-E3
| Parameters | |
|---|---|
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 54pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 3.31mm |
| Length | 39.7mm |
| Width | 14.73mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Weight | 4.190003g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 625mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG407 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Power Dissipation | 625mW |
| Max Supply Current | 500μA |
| Propagation Delay | 148 ns |
| Turn On Delay Time | 125 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
DG407BDJ-E3 Overview
As the electronic part is packed in 28-DIP (0.600, 15.24mm), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. 8:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, 28 terminations have occurred. The electronic part delivers high-quality output through its 8 channels. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 28 series that this electronic component is included. The multiplexer consists of 2 circuits. Use DG407 to search for variants of the digital switches. As far as internal resistance is concerned, it has 100Ohm. Datasheets for 28 pin functions are available upon request. Users shouldn't supply more than 36V voltage to the switch device. The digital multiplexer has a low cost Dual, Single supply. 7.5V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 30μA. A digital multiplexer may suffer damage if voltage is applied above 500μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using dual power supplies, you should attach at least 5V. The electrical part can be operated at 15V voltage levels. The electrical component supports 16 inputs.
DG407BDJ-E3 Features
8 Channels
30μA Supply Current
DG407BDJ-E3 Applications
There are a lot of Vishay Siliconix DG407BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Multiplexers
- Switching Systems
- Cell phones
- Residential Gateways, Home Gateway/Router
- Multi-Line E1 Interface Cards
- Audio signal routing
- Ultrasound
- Public switching systems
- Routers
