DG407BDN-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG407 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Propagation Delay | 163 ns |
| Turn On Delay Time | 125 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 94 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 86 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 54pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Time (Ton, Toff) (Max) | 107ns, 88ns |
| Charge Injection | 11pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG407BDN-E3 Overview
The electrical component comes in 28-LCC (J-Lead) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 8:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 28 terminations. The electronic part delivers high-quality output through its 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. There is an electrical component included in the 28 series. A total of 2 circuits make up this switch device. Try searching with DG407 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. To find out what the 28 pins do, please refer to the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. It is recommended to use 7.5V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 30μA current. Put voltage above 500μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 5V if you are using dual power supplies. 15V operating voltages are supported by the electronic component. Among the inputs that can be operated are the 16 inputs.
DG407BDN-E3 Features
8 Channels
30μA Supply Current
DG407BDN-E3 Applications
There are a lot of Vishay Siliconix DG407BDN-E3 Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Fiber to the Home
- CSU
- Avionics and Military Systems
- Audio and video signal routing
- Digital access cross connects
- Audio/video switches
- Microprocessor controlled systems
- Wireless Local Loop
- Video signal routing
