Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
28-SOIC (0.295, 7.50mm Width) |
Weight |
792.000628mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
Resistance |
100Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
450mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG407 |
Pin Count |
28 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
15V |
Number of Channels |
8 |
Number of Circuits |
2 |
Max Supply Voltage |
36V |
Min Supply Voltage |
7.5V |
Operating Supply Current |
30μA |
Max Supply Current |
500μA |
Propagation Delay |
148 ns |
Turn On Delay Time |
125 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
94 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
60Ohm |
Min Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
86 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
6pF 54pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Time (Ton, Toff) (Max) |
107ns, 88ns |
Charge Injection |
11pC |
Channel-to-Channel Matching (ΔRon) |
3 Ω |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height |
2.34mm |
Length |
17.91mm |
Width |
7.49mm |
RoHS Status |
ROHS3 Compliant |
DG407BDW-E3 Overview
As the electronic part is packed in 28-SOIC (0.295, 7.50mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 8:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 28 terminations have been recorded. As a result of its 8 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 28 pins is performed into the body of the electrical component. A total of 2 circuits make up this switch device. Try searching with DG407 to find analog multiplexer variants. There is 100Ohm internal resistance in this digital multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 7.5V. For this multiplexer to operate, 30μA current would be sufficient. If you put voltage higher than 500μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 5V. 15V operating voltages are supported by the electronic component.
DG407BDW-E3 Features
8 Channels
30μA Supply Current
DG407BDW-E3 Applications
There are a lot of Vishay Siliconix DG407BDW-E3 Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Fiber In The Loop (FITL)
- Imaging
- PCMCIA cards
- Medical Instrumentation
- Intelligent PBX
- Wireless Local Loop
- Sample-and-hold systems
- Multiplexers
- Private Branch Exchange (PBX)