DG407DJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Weight | 4.190003g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 625mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Pin Count | 28 |
| Operating Supply Voltage | 9V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 34V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 80μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 625mW |
| Max Supply Current | 100μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 65pF |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Height | 3.31mm |
| Length | 39.7mm |
| Width | 14.73mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
DG407DJ Overview
The electronic component is convenient to ship overseas because it is packed in a 28-DIP (0.600, 15.24mm). High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 8:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 28 terminations. A high-quality output is provided by the electrical component's 8 channels. A total of 28 pins are injected into the body of the electronic part. 2 circuits are used in this analogue multiplexer. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. For functions related to 28 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 34V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 5V voltage fed to the electrical part below 5V. This digital switch can be operated with a current of 80μA. Putting voltage greater than 100μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. A dual power supply should have at least 5V voltage attached. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER. Operating voltages range from 9V. There are 16 inputs to be operated. Drain to Source resistance for this electronic component is 100Ohm.
DG407DJ Features
8 Channels
80μA Supply Current
Drain-to-Source resistance: 100Ohm
DG407DJ Applications
There are a lot of Vishay Siliconix DG407DJ Analog Switches & Multiplexers ICs applications.
- ATM
- Microprocessor Controlled Analog Systems
- Precision data acquisition
- Data Acquisition Systems
- Wireless Local Loop
- PBX interfaces
- Signal routing between systems
- Video signal routing
- Microwave transmission systems
- Sample-and-hold systems
