DG407DJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Weight | 4.190003g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 625mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | DG407 |
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 7.5V |
| Operating Supply Current | 30μA |
| Power Dissipation | 625mW |
| Max Supply Current | 500μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 65pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Drain to Source Resistance | 50Ohm |
| Height | 3.31mm |
| Length | 39.7mm |
| Width | 14.73mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG407DJ-E3 Overview
Shipping overseas is convenient with the electronic component packed in 28-DIP (0.600, 15.24mm). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. The operating temperature is extended to around -40°C~85°C TA. 28 terminations have been made so far. The electronic part delivers high-quality output through its 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 28 series. Circuits number 2 make up this analogue multiplexer. DG407 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. Please refer to the datasheets for 28 pins functions. A voltage higher than 44V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 7.5V. For this multiplexer to operate, 30μA current would be sufficient. It may damage the digital multiplexer if the voltage is higher than 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. You should attach at least 5V voltage if you are using dual power supply. 15V operating voltages are supported by the electronic component. In order to operate the 16 inputs, there are several steps to follow. The Drain to Source resistance of this electronic component is 50Ohm.
DG407DJ-E3 Features
8 Channels
30μA Supply Current
Drain-to-Source resistance: 50Ohm
DG407DJ-E3 Applications
There are a lot of Vishay Siliconix DG407DJ-E3 Analog Switches & Multiplexers ICs applications.
- Routers
- Battery-powered systems
- SONET/SDH ADM
- Avionics test equipment
- Ultrasound
- Precision instrumentation
- Automatic test equipment
- Channel Banks
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital cross connects (DSX-1)
