DG407DN-T1
| Parameters | |
|---|---|
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Number of Functions | 1 |
| Reach Compliance Code | unknown |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 7.5V |
| Analog IC - Other Type | DPDT |
| Max Supply Current | 500μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 600 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 65pF |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 12.57mm |
| Width | 12.57mm |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Weight | 1.182714g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
DG407DN-T1 Overview
Shipping overseas is convenient due to the electrical component's packing in 28-LCC (J-Lead). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 28. A 8 channel electronic part produces high-quality output. Circuits number 2 make up this analogue multiplexer. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for functions of 28 pins are available. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 44V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. 7.5V is the lowest voltage that should be fed to the electronic electronic part. A voltage higher than 500μA may cause damage to the switch multiplexer. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 5V. A DPDT analog IC is integrated into the board. It can operate from 15V operating voltages.
DG407DN-T1 Features
8 Channels
DG407DN-T1 Applications
There are a lot of Vishay Siliconix DG407DN-T1 Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- Microprocessor Controlled Analog Systems
- Fiber to the Home
- E1 Network Equipment
- Industrial control systems
- Avionics and Military Systems
- DSUs
- Signal routing between systems
- PBXs
- Sample-and-hold systems
