DG408AK
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 900mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height | 3.94mm |
| Length | 19.56mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG408AK Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. The operating temperature is extended to around -40°C~85°C TA. There are 16 terminations totally. By its 8 channels, the electronic component provides high-quality output. This electrical component is included in the 16 series of products. There are 1 circuits in this switch device. In this multiplexer, the internal resistance is 100Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 44V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 13V. Putting voltage greater than 500μA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 5V voltage attached. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. It can operate from 36V operating voltages. It is possible to operate 8 inputs.
DG408AK Features
8 Channels
DG408AK Applications
There are a lot of Vishay Siliconix DG408AK Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Isolation
- Mechanical reed relay replacement
- Precision test equipment
- PDH Multiplexers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Precision data acquisition
- HDTV
- Digital access cross connects
- Relay replacements
