DG408AK-E3
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 900mW |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Current-Max (Isup) | 2mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 225ns |
| Signal Current-Max | 0.03A |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG408AK-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. Increasing operating temperature to around -40°C~85°C TA. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. The electronic part body is injected with 16 pins. 1 circuits are used in this analogue multiplexer. A 100Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 44V voltage to the switch device. The lowest voltage fed to the electronic component should be 13V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 5V if you are using dual power supplies. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. Operating 8 inputs is required.
DG408AK-E3 Features
8 Channels
DG408AK-E3 Applications
There are a lot of Vishay Siliconix DG408AK-E3 Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Communication systems
- FTTH
- Industrial
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multiplexers
- Relay Replacement
- Audio signal routing
- Data Acquisition Systems
- Frame Relay Equipment
