Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Through Hole |
Package / Case |
16-CDIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tube |
Published |
2000 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Pin Count |
16 |
Operating Supply Voltage |
28V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
500μA |
Propagation Delay |
250 ns |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
5V~30V ±5V~20V |
Supply Current-Max (Isup) |
2mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
4.5V |
Screening Level |
MIL-STD-883 Class B |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 26pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.5 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
5.08mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
DG408AK/883B Overview
Shipping overseas is convenient with the electronic component packed in 16-CDIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Through Hole position. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -55°C~125°C TA. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 8 channels. A 15V voltage supply should turn on and run the electronic component. This electronic part can be found in the 16 series. A total of 1 circuits make up this switch device. As far as internal resistance is concerned, it has 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 30V should not normally be supplied to the switches. 4.5V is the lowest voltage that should be fed to the electronic electronic part. 500μA current would be enough for this multiplexer to operate. Despite this switch device's dual supply capability, its voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. Operating voltages of 28V are compatible with the electrical part.
DG408AK/883B Features
8 Channels
500μA Supply Current
DG408AK/883B Applications
There are a lot of Maxim Integrated DG408AK/883B Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- E1 Network Equipment
- Routers
- Frame Relay Equipment
- Fiber to the Home
- DSUs
- DSLAMs
- PCMCIA cards
- Mechanical reed relay replacement
- Automotive applications