Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2002 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
175Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG408 |
Pin Count |
16 |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
30V |
Min Supply Voltage |
5V |
Operating Supply Current |
500μA |
Throw Configuration |
DPST |
Propagation Delay |
175 ns |
Turn On Delay Time |
600 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
5V~30V ±5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
2mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
300 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
5V |
Dual Supply Voltage |
9V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 26pF |
On-state Resistance Match-Nom |
1.5Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.5 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
225ns |
Signal Current-Max |
0.02A |
Height |
4.45mm |
Length |
19.43mm |
Width |
7.87mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG408DJ+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching with DG408 if you're looking for variants. A 175Ohm internal resistance characterizes this multiplexer. For details about the functions of 16 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 30V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 500μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 5V.
DG408DJ+ Features
8 Channels
500μA Supply Current
DG408DJ+ Applications
There are a lot of Maxim Integrated DG408DJ+ Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Isolation
- DSLAMs
- Cell phones
- Microwave transmission systems
- Low-Voltage
- Battery Powered Instruments
- Video switching
- Industrial control systems
- Multiplexers