DG408DJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Signal Current-Max | 0.02A |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
DG408DJ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 8:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 8 channels. 16 pins are injected to the electronic part body. This multiplexer is composed of 1 circuits. Analog switches have 100Ohm internal resistance. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 44V to the switch device in normal circumstances. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. A digital multiplexer may suffer damage if voltage is applied above 500μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. The voltage should be at least 5V if you are using dual power supplies. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. 36V operating voltages are supported by the electronic component. Drain to Source resistance is 100Ohm.
DG408DJ Features
8 Channels
Drain-to-Source resistance: 100Ohm
DG408DJ Applications
There are a lot of Vishay Siliconix DG408DJ Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- SDH/SONET multiplexers
- Channelized and Unchannelized DS3 applications
- Frame Relay Equipment
- ATM
- Microwave transmission systems
- Fiber to the Home
- DVD-R
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
