Parameters |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 26pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Height |
920μm |
Length |
5.07mm |
Width |
4.4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
90Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
265 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG408 |
Pin Count |
16 |
Operating Supply Voltage |
36V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Power Dissipation |
600mW |
Max Supply Current |
500μA |
Propagation Delay |
160 ns |
Turn On Delay Time |
150 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
8:1 |
DG408DQ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 8:1. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 16 terminations. A electrical component with 8 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. There are 1 circuits in this switch device. Try searching with DG408 if you're looking for variants. Analog switches have 90Ohm internal resistance. The datasheets for the 16 pins explain the functions. In normalcircumstances, users should not exceed 44V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 13V. An operating current of 1μA would be sufficient for this switch device. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. With dual power supplies, you should attach at least 5V. There is a voltage range of 36V operating voltages for the electrical part.
DG408DQ-E3 Features
8 Channels
1μA Supply Current
DG408DQ-E3 Applications
There are a lot of Vishay Siliconix DG408DQ-E3 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- PCMCIA cards
- Industrial control systems
- Access Concentrators
- Industrial and process control systems
- FTTH
- ATM
- Channel Banks
- E1 Network Equipment
- PDAs