DG408DY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 75μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 40Ohm |
| Signal Current-Max | 0.02A |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
DG408DY Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. There is 8:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 8 channels. An electrical component of this type can be found in the 16 series. A total of 1 circuits make up this switch device. This digital multiplexer has 100Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 36V to a switch device. The digital multiplexer has a low cost Dual, Single supply. 5V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 75μA current would be sufficient. Put voltage above 500μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. You should attach at least 5V voltage if you are using dual power supply. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. There is 40Ohm Drain to Source resistance on this electronic part.
DG408DY Features
8 Channels
75μA Supply Current
Drain-to-Source resistance: 40Ohm
DG408DY Applications
There are a lot of Vishay Siliconix DG408DY Analog Switches & Multiplexers ICs applications.
- PDAs
- Multiplexers
- Sample hold systems
- Battery-powered systems
- Audio signal routing
- Precision test equipment
- Audio and video switching
- High-Voltage
- Relay Replacement
- Isolation
