Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
100Ohm |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG408 |
Pin Count |
16 |
Operating Supply Voltage |
36V |
Number of Channels |
8 |
Voltage |
32V |
Number of Circuits |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
13V |
Operating Supply Current |
1μA |
Nominal Supply Current |
30mA |
Power Dissipation |
600mW |
Max Supply Current |
500μA |
Turn On Delay Time |
150 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 26pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
100Ohm |
Signal Current-Max |
0.02A |
Height |
1.75mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG408DY-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 8 channels. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. This multiplexer is composed of 1 circuits. Search with DG408 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 100Ohm. For functions related to 16 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 44V. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 13V voltage fed to the electrical part below 13V. 1μA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 500μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. If you are using a dual power supply, you should attach at least 5V. This electrical part is compatible with 36V operating voltages. This electronic component presents a Drain to Source resistance of 100Ohm.
DG408DY-E3 Features
8 Channels
1μA Supply Current
Drain-to-Source resistance: 100Ohm
DG408DY-E3 Applications
There are a lot of Vishay Siliconix DG408DY-E3 Analog Switches & Multiplexers ICs applications.
- Industrial
- Wireless Local Loop
- Remote Powered Equipment
- Cross Connects
- DVD-R
- Data switching
- Microprocessor Controlled Analog Systems
- SDH/SONET multiplexers
- Sample-and-hold systems
- USB 1.1 signal switching circuits