DG408DY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Nominal Supply Current | 10μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG408DY-T1 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 8 channels. A key feature of the 16 series is the inclusion of this electronic part as part of its design. It consists of 1 circuits. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 44V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage the electronic part should receive is 13V. The analogue multiplexer may be damaged if voltage is greater than 500μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. It is recommended that you attach at least 5V to your dual power supply. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. 36V operating voltages can be used with this electrical part. Among the inputs that can be operated are the 8 inputs.
DG408DY-T1 Features
8 Channels
DG408DY-T1 Applications
There are a lot of Vishay Siliconix DG408DY-T1 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Isolation
- Automotive applications
- Audio/video switches
- PCMCIA cards
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Fault Tolerant Systems
- Microwave transmission systems
- Avionics
- SDH
