DG408DY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Signal Current-Max | 0.02A |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG408DY-T1-E3 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 8:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. The circuits in this analogue multiplexer number 1. Try searching with DG408 if you're looking for variants. There is 100Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. A voltage higher than 44V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. 13V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. The analogue multiplexer may be damaged if voltage is greater than 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. For dual power supplies, a voltage of at least 5V should be attached. Operating voltages of 36V are compatible with the electrical part. Drain to Source resistance is 100Ohm.
DG408DY-T1-E3 Features
8 Channels
1μA Supply Current
Drain-to-Source resistance: 100Ohm
DG408DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG408DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Cable PC
- Digital Cross-Connects
- Optical Applications
- Cellular phones
- Data switching
- PDH Multiplexers
- Frame Relay Equipment
- USB 1.1 signal switching circuits
- Communication systems
- High-Voltage
