DG408EUE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 2mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG408EUE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 8 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. A total of 1 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with DG408. The internal resistance of this digital multiplexer is 175Ohm. To find out what the 16 pins do, please refer to the datasheets. normally, users should not supply switches with voltages higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. 5V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 500μA current. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. If you are using dual power supplies, you should attach at least 5V. This electrical part is compatible with 28V operating voltages.
DG408EUE+T Features
8 Channels
500μA Supply Current
DG408EUE+T Applications
There are a lot of Maxim Integrated DG408EUE+T Analog Switches & Multiplexers ICs applications.
- High-Voltage
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PBXs
- New designs requiring multiplexer functions
- PDAs
- T1/E1 Terminals
- Battery-powered systems
- RGB switches
- Multiplexers
- PBX interfaces
