DG408LDQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 17Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | VIDEO APPLICATION |
| Max Power Dissipation | 650mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG408 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 700μA |
| Power Dissipation | 650mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 29Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 20pF |
| Switch Time (Ton, Toff) (Max) | 55ns, 25ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -82dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 45ns |
| Signal Current-Max | 0.03A |
| Height | 920μm |
| Length | 5.07mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG408LDQ-T1-E3 Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 8 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. An electrical component of this type can be found in the 16 series. 1 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with DG408. An switch multiplexer with 17Ohm internal resistance has a value of 17Ohm. You can find the functions of the 16 pins in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 12V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2.7V. The switch device would be able to operate with 700μA current. Putting voltage greater than 500μA on the multiplexer may cause damage. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 3V. Additional features of the electronic component include: VIDEO APPLICATION.
DG408LDQ-T1-E3 Features
8 Channels
700μA Supply Current
Additional Features: VIDEO APPLICATION
DG408LDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG408LDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- PDAs
- CSU
- Relay replacements
- Fault Tolerant Systems
- ISDN NT1/TA
- Video switching
- New designs requiring multiplexer functions
- Audio and video switching
- SONET
- Communication systems
