DG408MY/PR-T
| Parameters | |
|---|---|
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 225ns |
| Switch-off Time-Max | 300ns |
| Signal Current-Max | 0.03A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Current-Max (Isup) | 2mA |
DG408MY/PR-T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 8:1. Around -55°C~125°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. Circuits number 1 make up this analogue multiplexer. As far as internal resistance is concerned, it has 100Ohm. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. 5V is the lowest voltage the electrical component should receive. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. A dual power supply should have at least 5V voltage attached. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC.
DG408MY/PR-T Features
8 Channels
DG408MY/PR-T Applications
There are a lot of Maxim Integrated DG408MY/PR-T Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- SDH/SONET multiplexers
- Relay Replacement
- SDH
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- ATM
- Access Concentrators
- Medical
- Cross Connects
- Intelligent PBX
