DG409DJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Reach Compliance Code | unknown |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 36V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 450mW |
| Max Supply Current | 500μA |
| Throw Configuration | 4PST |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 14pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 40Ohm |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
DG409DJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 4:1. The operating temperature is extended to around -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 4 channels. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using SP4T switching circuits. The circuits in this analogue multiplexer number 2. It has an internal resistance of 100Ohm. To find out what the 16 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 44V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 13V. Put voltage above 500μA on the multiplexer to cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 5V. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. The electrical part can be operated at 36V voltage levels. A 8 input needs to be operated. Drain to Source resistance for this electronic component is 40Ohm.
DG409DJ Features
4 Channels
Switch Circuit: SP4T
Drain-to-Source resistance: 40Ohm
DG409DJ Applications
There are a lot of Vishay Siliconix DG409DJ Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Wireless Local Loop
- Medical
- T1/E1 Terminals
- Multi-Line E1 Interface Cards
- Automatic test equipment
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical Instrumentation
- Industrial
