Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Weight |
1.627801g |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
40Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
450mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG409 |
Pin Count |
16 |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
36V |
Min Supply Voltage |
5V |
Operating Supply Current |
1μA |
Nominal Supply Current |
10μA |
Power Dissipation |
450mW |
Max Supply Current |
500μA |
Propagation Delay |
160 ns |
Turn On Delay Time |
150 ns |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
12V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 14pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω (Max) |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
100Ohm |
Height |
3.81mm |
Length |
21.33mm |
Width |
7.11mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG409DJ-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Through Hole. 4:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. There are 16 terminations totally. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. 16 pins are injected to the electronic part body. Based on SP4T switching circuits, these analog multiplexers work. A 2 circuit is present in this switch device. Using the DG409 search parameter, you can discover variants of the switch. There is 40Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 5V. The analogue multiplexer could operate on 1μA current. Putting voltage greater than 500μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 5V. There are 8 inputs to be operated. A Drain to Source resistance of 100Ohm is shown for this electronic part.
DG409DJ-E3 Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
Drain-to-Source resistance: 100Ohm
DG409DJ-E3 Applications
There are a lot of Vishay Siliconix DG409DJ-E3 Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- FTTH
- SDH/SONET multiplexers
- USB 1.1 signal switching circuits
- Central office
- Precision data acquisition
- Intelligent PBX
- Switching Systems
- Industrial
- PBXs