DG409DQ-E3
| Parameters | |
|---|---|
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 25pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Height | 920μm |
| Length | 5.07mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 90Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG409 |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 150 ns |
DG409DQ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. An electrical component of this type can be found in the 16 series. Unlike digital switches, these are based on SP4T switching circuits. This multiplexer is composed of 2 circuits. Using the DG409 search parameter, you can discover variants of the switch. A 90Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 44V. A analog switch ic that has a cost-effective Dual, Single supply type. 13V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 1μA. Putting voltage greater than 500μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 5V. 36V operating voltages can be used with this electrical part. Among the inputs that can be operated are the 8 inputs.
DG409DQ-E3 Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
DG409DQ-E3 Applications
There are a lot of Vishay Siliconix DG409DQ-E3 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Residential Gateways, Home Gateway/Router
- Remote Powered Equipment
- Audio and video signal routing
- Multi-Line E1 Interface Cards
- SDH
- Industrial and process control systems
- Cell phones
- HDTV
- DSLAMs
