DG409DY+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG409 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | 4PST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 14pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG409DY+T Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. Operating temperature extended to -40°C~85°C TA. In total, there have been 16 terminations. A electrical component with 4 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. An electrical component of this type can be found in the 16 series. A SP4T switching circuit is used to build these analog multiplexers. A 2 circuit is present in this switch device. Look for analog switch ic variants by searching with DG409. In this multiplexer, the internal resistance is 175Ohm. You can find the functions of the 16 pins in the datasheets. A voltage higher than 30V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 5V. For this digital switch to work, 500μA current would suffice. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 5V. 28V operating voltages are supported by the electronic component.
DG409DY+T Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
DG409DY+T Applications
There are a lot of Maxim Integrated DG409DY+T Analog Switches & Multiplexers ICs applications.
- PBX interfaces
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Precision data acquisition
- Private Branch Exchange (PBX)
- Video signal routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- MP3 players
- Battery Powered Systems
- HDTV
