banner_page

DG409DYZ-T

Analog Switches BREAK-BEFORE-MAKE 15V SOIC


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-DG409DYZ-T
  • Package: SOIC
  • Datasheet: PDF
  • Stock: 934
  • Description: Analog Switches BREAK-BEFORE-MAKE 15V SOIC(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Contact Plating Tin
Mount Surface Mount
Package / Case SOIC
Number of Pins 16
Published 1999
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 2
Number of Terminations 16
ECCN Code EAR99
Resistance 100Ohm
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Additional Feature ALSO OPERATE WITH 5V TO 34V SINGLE SUPPLY
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 15V
Time@Peak Reflow Temperature-Max (s) 30
Operating Supply Voltage 28V
Temperature Grade INDUSTRIAL
Number of Channels 2
Max Supply Voltage 40V
Min Supply Voltage 5V
Operating Supply Current 200μA
Throw Configuration 4PST
Propagation Delay 250 ns
Turn On Delay Time 180 ns
Logic Function Multiplexer
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 120 ns
Max Dual Supply Voltage 20V
Min Dual Supply Voltage 5V
High Level Output Current 30mA
Off-state Isolation-Nom 75 dB
On-state Resistance Match-Nom 15Ohm
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 150ns
Switch-off Time-Max 150ns
Height Seated (Max) 1.75mm
Length 9.9mm
Width 3.9mm
Radiation Hardening No
RoHS Status RoHS Compliant
Lead Free Lead Free

DG409DYZ-T Overview


The electronic part can be shipped overseas conveniently because it is packaged in SOIC. Total terminations are 16. High-quality output is provided by the electronic component's 2 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. The functions of 16 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 200μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 5V. Operating voltages of 28V are compatible with the electrical part. Check out the electrical component's additional features, such as the following: ALSO OPERATE WITH 5V TO 34V SINGLE SUPPLY. Temperatures higher than 85°C are not recommended for operation of the analogue multiplexer.

DG409DYZ-T Features


2 Channels
200μA Supply Current
Additional Features: ALSO OPERATE WITH 5V TO 34V SINGLE SUPPLY

DG409DYZ-T Applications


There are a lot of Intersil (Renesas Electronics America) DG409DYZ-T Analog Switches & Multiplexers ICs applications.

  • Precision test equipment
  • Microwave transmission systems
  • Sample hold systems
  • PBXs
  • Microprocessor Controlled Analog Systems
  • Imaging
  • Audio and video switching
  • SDH/SONET multiplexers
  • ISDN NT1/TA
  • ATM

Write a review

Note: HTML is not translated!
    Bad           Good