DG409EUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 755mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG409 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | 4PST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 14pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG409EUE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. The multiplexer consists of 2 circuits. Use DG409 to search for variants of the digital switches. This digital multiplexer has 175Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. 5V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 500μA current. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. It is recommended that you attach at least 5V to your dual power supply. A voltage of 28V can be used to operate the electronic component.
DG409EUE+T Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
DG409EUE+T Applications
There are a lot of Maxim Integrated DG409EUE+T Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Transmit
- Battery-powered systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Relay Replacement
- Remote wireless modules
- Precision data acquisition
- Residential Gateways, Home Gateway/Router
- Industrial and process control systems
- Industrial control systems
