DG409LDY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 29Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 16 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Nominal Supply Current | 10μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 29Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 20pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 55ns, 25ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -82dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 95ns |
| Drain to Source Resistance | 30Ohm |
| Signal Current-Max | 0.03A |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG409LDY Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. Operating temperature around -40°C~85°C TA extended. 16 terminations have been made so far. The electronic part provides high-quality output because it has 4 channels. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using SP4T switching circuits. Circuits number 2 make up this analogue multiplexer. An switch multiplexer with 29Ohm internal resistance has a value of 29Ohm. Please refer to the datasheets for 16 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 2.7V. Putting voltage greater than 500μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. The voltage should be at least 3V if you are using dual power supplies. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER. In order to operate the 8 inputs, there are several steps to follow. It has a Drain to Source resistance of 30Ohm ohms.
DG409LDY Features
4 Channels
Switch Circuit: SP4T
Drain-to-Source resistance: 30Ohm
DG409LDY Applications
There are a lot of Vishay Siliconix DG409LDY Analog Switches & Multiplexers ICs applications.
- Ultrasound
- CSU
- High-Voltage
- DSLAMs
- New designs requiring multiplexer functions
- Battery Powered Systems
- Sample-and-hold systems
- Wireless Local Loop
- Mechanical reed relay replacement
- Microprocessor controlled systems
