DG411AK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG411 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 Class B |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG411AK/883B Overview
The electrical component comes in 16-CDIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -55°C~125°C TA. In total, there are 16 terminations. This electronic part offers high-quality output due to its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 16 series. Circuits based on SPST - NC switching are used to construct these analog switch ics. A 4 circuit is present in this switch device. Try searching with DG411 to find analog multiplexer variants. It has an internal resistance of 30Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 10V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating voltages range from 28V.
DG411AK/883B Features
1 Channels
Switch Circuit: SPST - NC
DG411AK/883B Applications
There are a lot of Maxim Integrated DG411AK/883B Analog Switches & Multiplexers ICs applications.
- Industrial
- Audio and video routing
- PDAs
- MP3 players
- ISDN NT1/TA
- T1/E1 Terminals
- Communication systems
- Relay Replacement
- Relay replacements
- Remote wireless modules
