DG411CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Package / Case | PDIP |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Temperature Grade | COMMERCIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | SPST |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Off-state Isolation-Nom | 68 dB |
| On-state Resistance Match-Nom | 3Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG411CJ+ Overview
Packed in PDIP, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The total number of terminations is 16. A 1 channel electronic part produces high-quality output. A 15V voltage supply should turn on and run the electronic component. A key feature of the 16 series is the inclusion of this electronic part as part of its design. There is 45Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 30V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 10V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VThe voltage should be at least 4.5V if you are using dual power supplies. It is integrated with SPST analog ICs. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. In an environment with a temperature higher than 70°C, the digital switches should not operate.
DG411CJ+ Features
1 Channels
DG411CJ+ Applications
There are a lot of Maxim Integrated DG411CJ+ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- High speed data transmission line cards
- Medical systems
- Audio and video routing
- USB 1.1 signal switching circuits
- E1 Multiplexer
- Microwave transmission systems
- Automatic test equipment
- SONET/SDH ADM
- High-Voltage
