DG411CUE+T

175ns, 145ns SPST - NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG411 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-DG411CUE+T
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 760
Description: 175ns, 145ns SPST - NC 45Ohm Analog Switches BREAK-BEFORE-MAKE DG411 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Nominal Supply Current	100pA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Voltage - Supply, Single/Dual (±)	10V~30V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	30mA
Dual Supply Voltage	18V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	3 Ω (Max)
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	175ns
Normal Position	NC
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2010
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	80Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	457mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG411
Pin Count	16
Operating Supply Voltage	28V
Power Supplies	512/+-15V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	30V
Min Supply Voltage	10V
Operating Supply Current	100pA

DG411CUE+T Overview

Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around 0°C~70°C TA. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. The circuits in this analogue multiplexer number 4. Try searching with DG411 if you're looking for variants. There is 80Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 10V as the lowest voltage for the electrical part. For this digital switch to work, 100pA current would suffice. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. 28V operating voltages are supported by the electronic component.