DG411DQ-T1-E3
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | PURE MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Voltage - Supply, Single/Dual (±) | 5V~44V ±5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 220ns |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
DG411DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. There is an electrical component included in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. There are 4 circuits in this switch device. As far as internal resistance is concerned, it has 35Ohm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. 13V should be the lowest voltage fed to the electronic component. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. You should attach at least 7V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG411DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
DG411DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG411DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Relay replacements
- FTTH
- Precision data acquisition
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- CSU
- Fiber to the Home
- Automatic test equipment
- Digital cross connects (DSX-1)
- Fiber In The Loop (FITL)
