DG411DVZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | RoHS Compliant |
DG411DVZ Overview
The electrical component comes in TSSOP packaging, which makes it convenient to ship overseas. 16 terminations have been made so far. As a result of its 4 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. There is 80Ohm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 40V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. An operating current of 100pA would be sufficient for this switch device. Put voltage above 1μA on the multiplexer to cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The electronic component can function from 28V. In an environment with a temperature higher than 85°C, the digital switches should not operate.
DG411DVZ Features
4 Channels
100pA Supply Current
DG411DVZ Applications
There are a lot of Intersil (Renesas Electronics America) DG411DVZ Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Cross Connects
- Digital cross connects (DSX-1)
- Channel Banks
- Routers
- Automatic test equipment
- PDAs
- Multi-Line E1 Interface Cards
- Medical
- Digital Cross-Connects
