DG411DVZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
DG411DVZ-T Overview
As the electronic part is packed in TSSOP, international shipping is convenient. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. In this multiplexer, the internal resistance is 80Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 5V should be the lowest voltage fed to the electronic component. This multiplexer would work with 100pA current. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 20V. It is recommended that you attach at least 5V to your dual power supply. It can operate from 28V operating voltages. An environment with a temperature greater than 85°C should not be used to operate the digital switches.
DG411DVZ-T Features
1 Channels
100pA Supply Current
DG411DVZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG411DVZ-T Analog Switches & Multiplexers ICs applications.
- Industrial
- Fiber to the Home
- Medical systems
- High reliability control systems
- Intelligent PBX
- Avionics test equipment
- Battery Powered Instruments
- E1 Multiplexer
- PDAs
- Communications systems
