Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2010 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
80Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG411 |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
512/+-15V |
Number of Channels |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
100pA |
Nominal Supply Current |
100pA |
Max Supply Current |
100pA |
Throw Configuration |
SPST |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
45Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
3 Ω (Max) |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
45Ohm |
Normal Position |
NC |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG411DY+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. This electronic part offers high-quality output due to its 4 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. A SPST - NC switching circuit is used for these analog switches. Try searching for the analog switch ic with DG411 if you are looking for variants. As far as internal resistance is concerned, it has 80Ohm. Datasheets for functions of 16 pins are available. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 10V. For this digital switch to work, 100pA current would suffice. It may damage the digital multiplexer if the voltage is higher than 100pA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. Operating voltages range from 20V. The Drain to Source resistance of this electronic component is 45Ohm.
DG411DY+ Features
4 Channels
Switch Circuit: SPST - NC
100pA Supply Current
Drain-to-Source resistance: 45Ohm
DG411DY+ Applications
There are a lot of Maxim Integrated DG411DY+ Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Communication systems
- New designs requiring multiplexer functions
- SDH/SONET multiplexers
- Multi-Line E1 Interface Cards
- Low-Voltage
- PBX interfaces
- RGB switches
- Channelized and Unchannelized DS3 applications
- Signal routing between systems