DG411DY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~44V ±5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG411DY Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tube is used. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. Into the electrical component body are injected 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. There is 35Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. For this multiplexer to operate, 30mA current would be sufficient. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VYou should attach at least 7V voltage if you are using dual power supply. The 4 inputs need to be operated in order to work.
DG411DY Features
Switch Circuit: SPST - NC
30mA Supply Current
DG411DY Applications
There are a lot of Vishay Siliconix DG411DY Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Battery Powered Systems
- Signal routing between systems
- Medical systems
- RGB switches
- Medical
- USB 1.1 signal switching circuits
- PDH Multiplexers
- Video signal routing
- Power routing
