DG411DY-T1-E3

175ns, 145ns SPST - NC 35Ohm Analog Switches BREAK-BEFORE-MAKE DG411 16 Pins 250pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG411DY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 746
Description: 175ns, 145ns SPST - NC 35Ohm Analog Switches BREAK-BEFORE-MAKE DG411 16 Pins 250pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	80Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG411
Pin Count	16
Operating Supply Voltage	15V
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	1μA
Nominal Supply Current	100pA
Power Dissipation	600mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	175 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	5V~44V ±5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	7V
High Level Output Current	30mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	5pC
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	220ns
Drain to Source Resistance	45Ohm
Normal Position	NC
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG411DY-T1-E3 Overview

The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. SPST - NC switching circuits are used in these analog switch ics. Try searching with DG411 to find analog multiplexer variants. As far as internal resistance is concerned, it has 80Ohm. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 13V. This digital switch can be operated with a current of 1μA. Putting voltage greater than 1μA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. It can operate from 15V operating voltages. Operating 4 inputs is required. Resistivity from Drain to Source is 45Ohm for this electronic part.