DG411DYZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 5μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Drain to Source Resistance | 25mOhm |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG411DYZ Overview
As the electronic part is packed in SOIC, international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Bulk. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. A 15V voltage supply should turn on and run the electronic component. Internally, this switch multiplexer has a resistance of 80Ohm. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 40V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 5V. 100pA current would be enough for this multiplexer to operate. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using a dual power supply, you should attach at least 5V. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 28V. Temperatures above 85°C should not be used to operate the switches. There is 25mOhm resistance between Drain and Source for this electronic part. The switch device is capable of conducting in a 4-bit mode.
DG411DYZ Features
1 Channels
100pA Supply Current
Drain-to-Source resistance: 25mOhm
4-Bit
DG411DYZ Applications
There are a lot of Intersil (Renesas Electronics America) DG411DYZ Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- PDAs
- Optical Applications
- Multi-Line E1 Interface Cards
- DSLAMs
- E1 Multiplexer
- Sample-and-hold systems
- Residential Gateways, Home Gateway/Router
- E1 Network Equipment
- HDTV
