DG411DYZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 28V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Off-state Isolation-Nom | 68 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG411DYZ-T Overview
As the electronic part is packed in SOIC, international shipping is convenient. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An switch multiplexer with 80Ohm internal resistance has a value of 80Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 40V in normal situations. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 5V. In order to operate this switch device, it would need a current of 100pA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. When using dual power supplies, you should attach at least 5V. The electronic component can function from 28V. Temperatures over 85°C should not be allowed for the multiplexer to operate. It can conduct in a 4-bit manner.
DG411DYZ-T Features
1 Channels
100pA Supply Current
4-Bit
DG411DYZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG411DYZ-T Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Precision test equipment
- Public switching systems
- Wireless Local Loop
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Medical Instrumentation
- DSUs
- Residential Gateways, Home Gateway/Router
- Precision data acquisition
- Industrial and process control systems
